Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Parts & Welding in Gardena: What to Know First
We provide independent Ghost Controls gate parts and welding service in Gardena, and most hinge, roller, and bracket repairs on Ghost Controls systems are completed in a single visit. The honest price posture is this: simple bracket and hinge work typically runs $180 to $340, while welding-in a new post or rebuilding a rail can run $500 to $1,100 depending on steel thickness and access. We quote the price before any work starts, and the number we quote is the number you pay.
This page is for Gardena homeowners who own a Ghost Controls gate opener and have a problem that is not the motor: a sagging gate, a broken hinge, a post that has rotted at the base, or a roller that has ground itself flat. If that sounds like your situation, call (916) 398-2696 and tell us what the gate is doing. A live person answers, day or night.
How Ghost Controls Products Fail, and How We Fix Them
Ghost Controls builds solid residential operators, but the metal around them takes a beating in Gardena. After 42 years working gates across this city, mostly in neighborhoods like Norwood Park, Hollypark, and El Camino Village, we know where these systems give out. Here are the failure modes we see most.
- Sagging gate leaf on the R series (AXZL, TDS2, SLS). Ghost Controls R-series operators push a fair amount of weight for their size, and when a leaf sags even an inch, the opener arm strains against the misalignment every cycle. The root cause is almost always a worn top hinge pin or a hinge bracket that has pulled loose from the post. We replace the hinge with a heavier gauge pair and weld the bracket back square. The motor usually does not need to be touched.
- Post corrosion at the soil line, common on all Ghost Controls slide gate installs. Gardena sits close enough to the coast that morning marine air settles over the South Bay, and steel posts set directly in concrete sweat at the base. We regularly cut out a corroded post in Gardena, weld in fresh schedule 40 steel, and re-hang the gate level. The opener’s limit settings stay valid when the gate hangs true, which avoids the Ghost Controls system fighting itself on every open cycle.
- Gate roller failures on Ghost Controls sliding gate kits. The factory rollers on Ghost Controls slide kits are adequate for a few years, but on heavier gates the bearings seize, and homeowners hear a grinding sound as the flat spot develops. We install sealed-bearing rollers rated above the gate’s actual weight and set the track spacing. The gate moves quietly, and the motor draws less current.
- Stripped motor bracket bolts on the D-series (DSL1, DTP1, DAB1). Ghost Controls D-series openers mount to the gate post with bolts that can work loose over time as the gate cycles thousands of times. Once the bracket wiggles, the bolt holes wallow out and the opener kicks against the slop. We weld in new plate steel, re-drill clean mounting holes, and retorque the bracket. No more wallow, no more strain on the drive arm.
- Latch and lock alignment after structural repairs. Ghost Controls systems rely on a gate that closes to the same point every time. When we weld a hinge or replace a roller, the latch bar and strike plate often need re-alignment to within a quarter inch. We adjust the mechanical latch, not just the opener limits, so the gate locks physically, not just electronically.
Our Ghost Controls Gate Parts & Welding Process
Every Ghost Controls parts and welding job in Gardena follows the same path. Here is what happens from the first call to the final test.
- 1
You call, a person answers. You describe the symptom: sag, scrape, grind, rust, or a gate that simply will not stay on its track. We schedule a visit at a time that works for you.
- 2
We inspect and diagnose. Our technician measures the gate’s weight, checks every hinge, roller, bracket, and post, and confirms the Ghost Controls operator is still sound. We tell you what is wrong and what can wait.
- 3
We give you a fixed price before work starts. Parts, labor, welding time, disposal. You approve the number first. No surprises on the bill, ever.
- 4
We do the work. Hinge replacement, post welding, rail repair, roller swap, latch re-alignment. We use OEM Ghost Controls parts when the warranty matters, and quality aftermarket steel and bearings where they exceed the factory spec.
- 5
We test under load. The gate opens and closes ten times, stops at the limits, and locks properly. We watch for strain, listen for sound differences.
- 6
You get the 90-Day Done Right Promise in writing. If anything is not right, we come back and make it right. No paperwork, no arguing, no exceptions.
What Ghost Controls Gate Parts & Welding Costs in Gardena
Prices in Gardena track steel weight, access, and how much of the original hardware we can save. Here are honest ranges for the jobs we do most.
- Hinge replacement (pair): $180 to $340, including grinding off the old hinges and welding on new heavier-gauge ones.
- Post replacement (single, welded): $450 to $900, depending on post size, concrete removal, and gate weight.
- Rail repair or reinforcement: $350 to $800, including straightening, welding gusset plates, and repainting the repaired section.
- Roller replacement (set of two or four): $150 to $320, sealed-bearing rollers rated for the gate’s actual weight.
- Latch and lock re-alignment: $120 to $240, after any structural work changes the gate’s closing point.
What moves the price is steel thickness, the condition of what we are welding to, and whether the gate has to come off its track to do the job right. We will tell you the exact number before we start. Call (916) 398-2696 for a free estimate. And remember: the older work often costs less than you think, because a straight gate is a cheap gate to run.
Why Gardena Homeowners Call Ironworks Gate Co. for Ghost Controls Work
We have been doing gates in Gardena since 1984. Victor Salinas grew up in Norwood Park, where half the block had a sliding driveway gate and the other half wished they did. That is not a marketing line; it is why we answer the phone and why we show up.
Our technicians are trained on Ghost Controls equipment, and they are also trained on LiftMaster, Mighty Mule, and DoorKing. If your Ghost Controls opener ever fails and the parts decision gets complicated, we can talk straight about your options without pushing a brand. Every job is covered by the 90-Day Done Right Promise. Every quote is fixed before we touch a bolt. And the person who answers your call at 2 a.m. is a person, not a recording.
We are an independent Ghost Controls service provider. We are not authorized by Ghost Controls, and we do not need to be. We have been fixing gates in this city for over four decades. A gate should open when you need it to. That is the whole job.
FAQs
Yes. We keep common Ghost Controls parts in stock, including arms, brackets, replacement remotes, and receiver boards. For less common components, we order directly through our supply channels and typically have the part within one to three business days. If a part is backordered, we tell you up front and can often install a temporary fix that keeps the gate operable until the OEM part arrives. Call (916) 398-2696 and we will check availability while you are on the phone.
Welding on the gate leaf, hinge brackets, or posts does not affect the Ghost Controls operator’s warranty in most cases, because the operator is a separate component and is not being modified. If the welding work changes the gate’s weight significantly, we will tell you before we start, because a heavier gate can strain the motor beyond its rated capacity. We protect the opener’s electronics by disconnecting power before any welding. As an independent Ghost Controls service provider, we take care not to open the motor housing or alter factory wiring, which keeps any remaining manufacturer warranty intact.
Most hinge replacements are completed on the first visit, and many are done the same day you call. We stock heavy-gauge weld-on hinges in our Gardena service trucks, and if the post is sound, the repair takes one to two hours. If the post itself is rotted or cracked, we will need to weld in a new post, which may require an extra day to set the concrete properly. Call (916) 398-2696 and describe what you are seeing; we will give you an honest time window, not a maybe.
If the gate leaf is structurally sound and the damage is confined to hinges, brackets, or a single post, repair is almost always the better value in Gardena. A quality welded repair on a reasonably maintained steel gate can outlast the opener itself. Replacement only makes sense when the gate frame is rusting through in multiple places, or you want to change the gate’s design entirely. We will tell you straight if your gate is worth saving; we have turned down replacement work that a less honest shop would have taken.
Yes. We replace worn Ghost Controls slide gate rollers with sealed-bearing units rated for the gate’s actual weight, and we weld and reinforce damaged track sections where the gate rides. If the track has shifted, we re-level it and set the spacing. This is one of the most common Ghost Controls service calls we handle in Gardena, and most roller and track repairs are completed in a single visit. Call (916) 398-2696 for a free estimate.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Gardena and nearby areas.