Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Parts & Welding in Gardena: What to Know First
Independent FAAC gate parts and welding service in Gardena typically runs $240 to $680 for most hinge, rail, and roller repairs, with custom welding work quoted by the job after we see the gate in person. We turn around most FAAC parts and welding repairs same visit, and a live person answers the phone 24 hours a day so you’re never chasing a callback. This page is for Gardena homeowners with a FAAC opener whose gate has started dragging, sagging, refusing to latch, or grinding against its rail, and who want someone who will tell them straight what needs fixing and what can wait.
If your FAAC gate needs parts or welding in Gardena, call (916) 398-2696. We quote the price before work starts, and it does not change when the invoice comes.
Key Takeaways
- Most FAAC gate welding and bracket repairs are completed same visit, with the price settled before we turn a bolt.
- We use genuine FAAC parts where the opener’s safety and warranty depend on it, and quality aftermarket parts where the savings make sense and the fit is identical.
- Every FAAC gate job in Gardena is backed by our written 90-Day Done Right Promise.
- A live person answers (916) 398-2696 any hour, any day, never a voicemail tree.
How FAAC Products Fail - and How We Fix Them
FAAC builds a solid operator. The 400 and 402 series, the 770 and 844 hydraulic rams, and the swing-arm models we see all over Gardena are good machines. What fails around them is usually the metal: the steel that holds the operator to the post, the hinge that carries the gate’s weight, the rail the gate rides on. Here are the failures we fix most, by model line.
- FAAC 400/402 swing gate arms: the bracket lets go, not the motor. These compact rams get mounted on a steel bracket bolted to the post, and on a heavy gate in a Gardena neighborhood with steady winds off the 405 corridor, the bracket itself fatigues. The arm works fine, but the gate starts jerking or stalling because the operator is no longer anchored square to the leaf. We cut out the old bracket, weld a new one plumb with the hinge line, and the gate runs true again.
- FAAC 770 series underground operators: the foundation box detaches from the rebar cage. The 770 is a fine underground operator, but the steel box that houses it gets welded to the gate’s structural frame. After years of traffic and ground shift in Gardena’s clay-heavy soil, those welds crack and the box starts moving independently of the gate. The symptom is a gate that opens twelve inches, stalls, and reverses. The fix is grinding out the cracked welds, re-welding the box with full penetration, and re-coating the joint so moisture stays out.
- FAAC 844 hydraulic rams: leaking fluid looks like an electrical problem. Homeowners often call us thinking the control board failed because the gate moves slower and slower. On a FAAC 844, the usual culprit is a seal leaking inside the ram itself. That’s a part we replace rather than patch, and while the ram is off, we check the mounting ears and clevis pins for wear. Half the time the pin is egg-shaped and needs replacing too, a ten-dollar part that saves the whole assembly.
- FAAC sliding gates: the rail wears where the roller parks on a hot afternoon. Steel expands in heat, and a black gate baking in the Gardena sun grows long enough to shift where each roller sits on the rail. Over time the rail develops a wear groove at exactly that spot, and the gate starts thumping every time it passes. We weld the worn section, grind it smooth, and sometimes use a hardened rail cap so the same wear doesn’t come back in three years.
- Gate leaf hinges on FAAC swing systems: the operator outlives the hinge, every time. A FAAC swing operator is rated for a gate up to a certain weight, but the original builder’s hinges often were not. After fifteen or twenty years, the leaf drops a quarter inch, the operator strains against it, and the gate starts faulting. We replace worn hinge pins, or weld in new hinge brackets sized for the actual weight of the leaf, then re-set the operator limits so it closes flush without over-pushing.
Our FAAC Gate Parts & Welding Process
When you call us about a FAAC gate in Gardena, here is how the job goes, from first call to closing the gate behind us.
- 1
You talk to a person, not a menu. Call (916) 398-2696 and a dispatcher who knows gate systems asks what the gate is doing, when it started, and what brand is on the opener. We book a service window that fits your day.
- 2
The technician shows up in uniform and reads the gate before turning a wrench. We check hinge wear, rail alignment, roller condition, and the operator’s mounting points. On a FAAC job, we power the system down before touching the gate so the opener cannot cycle against our hands.
- 3
We give you the price before work begins. We explain what needs replacing, what we can weld and save, and what a genuine FAAC part costs versus a quality aftermarket part. You approve the number before we start. The number does not change after we start.
- 4
The welding and parts replacement happens on-site. Most brackets, hinges, rails, and latch mounts can be cut out, prepped, welded, and ground in one visit. We carry a full set of common hinges, rollers, latch hardware, and FAAC operator mounts on the truck.
- 5
We run the gate through its full cycle ten times. Open, close, interrupt mid-cycle, reverse. We adjust the operator limits and force settings so the gate closes the way it did when it was hung.
- 6
You get the written 90-Day Done Right Promise. If that gate does not open and close correctly for ninety days, we come back and make it right. No paperwork, no arguing. That is the whole point of hiring someone who welds for a living.
What FAAC Gate Parts & Welding Costs in Gardena
Here are real numbers for the FAAC repairs we do most often in Gardena. These are honest ranges, quoted before work starts, with no surprise line items at the end.
- Hinge replacement with welding: $240-$520, depending on the weight of the leaf and how much of the post needs rebuilding.
- Post replacement and re-anchoring: $480-$900, including cutting out the old post, setting a new sleeve or replacement post, and re-hanging the gate to FAAC spec.
- Rail repair and welding: $220-$560, depending on the length of the wear section and whether we add a hardened cap.
- Custom welding (brackets, mounts, latch plates, gate frame repair): $180-$650, quoted after we see the gate, with the hourly welding rate stated up front.
- FAAC operator mounting bracket replacement: $260-$480, including re-welding the bracket square with the hinge line and re-setting operator limits.
- Gate rollers and latch/lock replacement: $140-$380 for common FAAC sliding gates and swing gates, including adjustment.
What moves the price is the weight of the gate, how much of the existing steel is salvageable, and whether the operator itself needs attention while we’re in there. We will always tell you the number before the grinder comes out. Call (916) 398-2696 for a free, exact estimate on your FAAC gate.
Why Gardena Homeowners Call Ironworks Gate Co. for FAAC Work
We have been working on driveway gates in Gardena for over 42 years, since 1984, and we plan to be here another forty. FAAC is one of nine opener brands we are trained and equipped on, and that matters more than it sounds like. If your FAAC operator needs a part, we handle it. If the day comes that the operator is beyond saving, we can install and program a LiftMaster, Mighty Mule, Ghost Controls, or DoorKing opener on the same gate, same visit, without calling a second company.
Every FAAC job we complete, from a simple hinge to a full post replacement, is covered by our written 90-Day Done Right Promise. Victor Salinas grew up in the Norwood Park neighborhood of Gardena, where half the block had a sliding driveway gate and the other half wished they did. He is the reason our technicians are background-checked, uniformed, and expected to treat your driveway the same way they would their own mother’s. We answer the phone 24 hours a day, every day. A gate should open when you need it to. That is the whole job.
FAQs
It depends on what the part is. As an independent FAAC service provider, we follow the same standard any honest repair company does: load-bearing and safety parts like operator arms, mounting brackets they will hold, and control boards get genuine FAAC components when the equipment is still under warranty. Non-warranty wear parts like hinges, rollers, and latch plates can use quality aftermarket options that fit and wear identically. We will always tell you which choice keeps your warranty intact and which one just saves you money.
Almost always, yes. Most bracket, hinge, and rail welding on a FAAC gate can be completed in one visit because we carry the common materials and parts on the truck. The steel needs to cool before we paint or coat it, which adds some time, but the gate is typically back in operation the same day. If it is a big custom job, we schedule the work and give you a firm price first.
Look at what the gate does when it moves. A gate that needs adjustment usually opens too far, slams shut, or reverses near the closed position. A gate that needs welding usually sags, scrapes the ground, jerks mid-cycle, or makes a grinding sound where the rail passes the roller. If the leaf moves up and down relative to the post when you push it by hand, that is worn metal, not an operator setting. Call (916) 398-2696 and we’ll tell you which one it is, usually over the phone.
The ones we see most are the FAAC 400 and 402 swing arms, the 770 underground operators, and the 844 hydraulic rams. We also service older FAAC models that are no longer made, which matters in Gardena because many of these gates were installed in the 1990s and early 2000s and the homeowners have no interest in replacing a gate that can still be fixed.
If the steel is sound and the problem is brackets, hinges, rollers, or a worn rail, repair is almost always the right call. A new gate plus new operator in Gardena runs thousands of dollars. A weld repair on a FAAC gate is measured in hundreds. We will only recommend replacement when the frame itself has rusted through or the gate has been hit hard enough to twist the structure. We are happy to give you a straight answer either way, and estimates are free.
Call Ironworks Gate Co. for Your FAAC Gate in Gardena
We have been fixing driveway gates in Gardena since 1984, and we stand behind every FAAC parts and welding job with a written 90-Day Done Right Promise. Done right, and backed in writing. Call (916) 398-2696 now for a free estimate, answered by a live person, any hour, any day. You will get a square deal: the price settled before we start, and the gate closing like the day it was hung.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving Gardena and nearby areas.